Matte Metallic Blue wrapped R1T

Administrator · May 16, 2022

Corey T's Rivian R1T wrapped in 3M Matte Metallic Blue vinyl. :like:

Rivian R1T R1S Matte Metallic Blue wrapped R1T 280434104_10161734231013275_7017432625567000822_n

Rivian R1T R1S Matte Metallic Blue wrapped R1T 280958689_10161734231073275_456531898886636789_n

Rivian R1T R1S Matte Metallic Blue wrapped R1T 280754156_10161734231203275_8156793056505694749_n

Rivian R1T R1S Matte Metallic Blue wrapped R1T 280938897_10161734230958275_2104924795201439429_n

Rivian R1T R1S Matte Metallic Blue wrapped R1T 280498777_10161734230903275_7239778442472292888_n

Rivian R1T R1S Matte Metallic Blue wrapped R1T 278771830_10161681902733275_2573231015652011566_n

R1Sky Business · May 16, 2022

Very nice

R1Sky Business · May 16, 2022

If you don't mind? What's the cost?

opnwide · May 16, 2022

Cory, that's cool! Matching shirt +1 !!

Mike Hunt · May 16, 2022

Do they remove the Rivian letters on the back and sides before the wrap?

SeaGeo · May 16, 2022

Mike Hunt said:
Do they remove the Rivian letters on the back and sides before the wrap?

Typically.

LoneStar · May 16, 2022

i'd rather Stealth PPF over RIvian Blue for similar effect yet enjoying that fancy paint

R1Sky Business · May 16, 2022

SeaGeo said:
Typically.

And then glue them back?

SeaGeo · May 16, 2022

R1Sky Business said:
And then glue them back?

Yeah.

The hood ornament is mechanically fixed to the truck.

opnwide · May 16, 2022

SeaGeo said:
Yeah.

The hood ornament is mechanically fixed to the truck.

Brice, actually the hood ornament has two, non-retentive positioning pins/dimples that, contrary to initial thoughts, do not mechanically clip into place. It is affixed via adhesive, and the two dimple positioners are set at odd angles that match the depression in the metal hood to make sure that the top and bottom of the logo are not turned 90 degrees by the installers in the factory. Same thing applies to the R1S logo on C-pillar.

AllInev · May 16, 2022

opnwide said:
Brice, actually the hood ornament has two, non-retentive positioning pins/dimples that, contrary to initial thoughts, do not mechanically clip into place. It is affixed via adhesive, and the two dimple positioners are set at odd angles that match the depression in the metal hood to make sure that the top and bottom of the logo are not turned 90 degrees by the installers in the factory. Same thing applies to the R1S logo on C-pillar.

@opnwide Thanks for this info. Given you know these details, I have a question for you:

I'm going to attached an emblem/badge to the lower-right tailgate panel. What's a good adhesive to use?

Ideally, the adhesive is strong enough that the badge/emblem never falls off, but something I could remove if I wanted or needed to.

opnwide · May 16, 2022

AllInev said:
@opnwide Thanks for this info. Given you know these details, I have a question for you:

I'm going to attached an emblem/badge to the lower-right tailgate panel. What's a good adhesive to use?

Ideally, the adhesive is strong enough that the badge/emblem never falls off, but something I could remove if I wanted or needed to.

That's slightly above my paygrade for the forums, but I know you can easily find double-sided 3m adhesive tape on amazon if you search for emblem adhesive. When they remove emblems, they use dental floss behind to work off the emblem and a heat gun to soften the adhesive. I'd err less adhesive tape than more unless the badge is valuable to you.

Polar · May 16, 2022

R1Sky Business said:
If you don't mind? What's the cost?

I’d say that’s a $4-6k wrap depending on region.

The satin metallic wrap on my MachE was $4k. I never knew wraps were so spendy until I committed to wrapping my MachE.

ja_kub_sz · May 17, 2022

So this was a stock Rivian Blue with a wrap?

Looks incredible! ??

sevengroove · May 17, 2022

ja_kub_sz said:
So the s was a stock Rivian Blue with a wrap?

Looks incredible! ??

I was wondering the same - it sounds like the wrap itself is a matte metallic blue color, so I doubt the truck is also Rivian Blue. That would have been a waste of $2.5k! My guess is that it's either GW or LAS.

Matte Metallic Blue wrapped R1T

Administrator

Administrator

R1Sky Business

Well-Known Member

R1Sky Business

Well-Known Member

opnwide

Well-Known Member

Mike Hunt

Well-Known Member

SeaGeo

Well-Known Member

LoneStar

Well-Known Member

R1Sky Business

Well-Known Member

SeaGeo

Well-Known Member

opnwide

Well-Known Member

AllInev

Well-Known Member

opnwide

Well-Known Member

Polar

Well-Known Member

ja_kub_sz

Well-Known Member

sevengroove

Well-Known Member

Similar threads