EV SportsLine Bed Liner Fits Like a Glove

[Careychastain]

Received my R1T Bed Liner from EV SportsLine Today. Very happy with the quality and fit.

https://evsportline.com

Sponsored

 

[kylealden]

Good fit. I'd love to see one of these with an infill to match the slats in the bed (for a flat for), but it's good to have an option!

 

[the long way downunder]

Good fit. I'd love to see one of these with an infill to match the slats in the bed (for a flat for), but it's good to have an option!

Agreed. "Fits like a glove" except it doesn't fit the fingers … : )
I use a piece of cardboard (replaced as it gets wet) as a slider the width between the wheel arches. I put a couple of large, watertight plastic boxes on the cardboard.

That's what I think is necessary for this bed because of the reach-over length of the gooseneck tailgate.

I'm thinking of a bed liner that's a thin sheet of slippery plastic on the underside with a handle rail across the front (for pulling) and a head rail (the width between the wheel arches, against the cabin as part of a frame) and side rails (for pushing the head rail to slide the bed liner back up to the cabin.) The side rails could be telescopic so the bedliner could vary in length and doesn't need to project 2-3 feet out over the open tailgate. The handle rail could have the bed liner on a recoiling roller so that the side rails telescope and retract as the bed liner material winds on the handle rail roller. The whole apparatus could roll up and be stored in a tube that's hanging from the roof of the gear tunnel.

 

[kizamybute']

Received my R1T Bed Liner from EV SportsLine Today. Very happy with the quality and fit.

https://evsportline.com

Do love the fit. My only concern was with how much those hexagons will collect dirt. Let us know your thoughts on it after having it in there for a little while. If not bad, will likely order one. Been waiting for some customer feedback first.

 

[Gavinmcc]

What does it look like with the hexagons down?

 

[suprteck]

Do love the fit. My only concern was with how much those hexagons will collect dirt. Let us know your thoughts on it after having it in there for a little while. If not bad, will likely order one. Been waiting for some customer feedback first.

I was thinking the same thing about the dirt. Was thinking about the other designs they have

 

[teddyang]

here's what the other design looks like...

 

[kizamybute']

here's what the other design looks like...

Oh wow, didn't realize they had other designs. Guess I need to look a little closer.

My current mat just has ribbed strips the run the length of the bed. The photos you provided above look better. I wouldn't mind just a solid surface of rubber with no strips / patterns / etc.

Wondering how the weight of the mat is. Heavy enough that it will stay in place if the tonneau is open? Mine is a thick heavy rubber that's definitely not going anywhere. These look quite a bit lighter and thinner. Would certainly make it easier to get in and out for cleaning. Just want to make sure the wind can't grab a hold of it while on the freeway?

This is what I currently have. Also, due to the thickness of mine, don't really notice the ridges built into the bed. Mine just doesn't wrap around the wheel wells

Looking at your image, the areas I marked in red (in image below. One in the corner, looks like it might need a little trimming to fit perfectly?

Also, the part below the tailgate, would have been nice if they extended it to fill in the that gap where you can see the plastic below......

 

[teddyang]

Oh wow, didn't realize they had other designs. Guess I need to look a little closer.

My current mat just has ribbed strips the run the length of the bed. The photos you provided above look better. I wouldn't mind just a solid surface of rubber with no strips / patterns / etc.

Wondering how the weight of the mat is. Heavy enough that it will stay in place if the tonneau is open? Mine is a thick heavy rubber that's definitely not going anywhere. These look quite a bit lighter and thinner. Would certainly make it easier to get in and out for cleaning. Just want to make sure the wind can't grab a hold of it while on the freeway?

according to the website:
the hexagon pattern weighs 16 lb
the flat pattern I have weighs 24 lb

I didn’t weigh it but the heft of it did surprise me. Don’t think it’s gonna go anywhere *knock on wood* (I mostly drive with the tonneau closed anyway)

 

[Prime]

here's what the other design looks like...

Definitely like this.

 

[windblowlc]

Mine's in transit. Flat mat like Ted's.

 

[KyleJJ06]

My flat one should be here tomorrow as well

 

[BobinIndy]

My flat one should be here tomorrow as well

Did you get your flat mat? How’s the fit and look (pics)?

 

[JamesPolk24]

Looks like a DIYer cut a piece of rubber mat to fit. Sloppy. Hope Husky makes something for the bed. Would probably be cheaper as well.

 

[Ralph]

Oh wow, didn't realize they had other designs. Guess I need to look a little closer.

My current mat just has ribbed strips the run the length of the bed. The photos you provided above look better. I wouldn't mind just a solid surface of rubber with no strips / patterns / etc.

Wondering how the weight of the mat is. Heavy enough that it will stay in place if the tonneau is open? Mine is a thick heavy rubber that's definitely not going anywhere. These look quite a bit lighter and thinner. Would certainly make it easier to get in and out for cleaning. Just want to make sure the wind can't grab a hold of it while on the freeway?

This is what I currently have. Also, due to the thickness of mine, don't really notice the ridges built into the bed. Mine just doesn't wrap around the wheel wells

Looking at your image, the areas I marked in red (in image below. One in the corner, looks like it might need a little trimming to fit perfectly?

Also, the part below the tailgate, would have been nice if they extended it to fill in the that gap where you can see the plastic below......

Received my smooth version and as pictured it also could use some trimming around both corners exactly as shown.

Sponsored